Good evening! The Brophy Stake Pocket Tie Down Anchor item # TL2B you were looking at is going to be your best option. They fit the standard 2" x 4" stake pocket, have a 4,000 lbs capacity each, and measure 8-1/4" tall x 3-1/2" wide x 1-1/2" deep. These are sold individually.
This tie down anchor will go through your stake pocket and will be secured by a pin that goes through the bottom. The Brophy Stake Pocket Tie Down Anchor item # TL2B is made in the USA and weighs 5 lbs.
I have... view full answer...
Hey Mark, so we don't have a stainless steel version of the Brophy D-Ring Tie Down Anchor part # RR05 but it sounds like you are worried about dissimilar metal causing corrosion so what you could do is use this but put some gardening plastic between the mounting plate and the aluminum and you'd be fine. That's what we do here when we install steel gooseneck hitches in aluminum truck bed. view full answer...
The WLL of the Brophy D-Ring Tie Down Anchor w Backing Plate # RR5K is always going to be 1,600 lbs. The only thing Brophy and other companies measure is what their anchor is capable of on its own. There are too many factors to determine what all of the possible kinds of wood or other surfaces this could be installed on can handle. view full answer...
Yes, the Brophy D-Ring Tie Down Anchors # DR01 will work with the Torklift FastGun Turnbuckles # TLS9529-2-LK. Generally, these kinds of D-Rings are not used as a tie down point for a camper, but if they are properly secured using the Backing Plate # BP1D, I see no reason why these could not be used for this purpose. I am not sure exactly what kind of camper you are securing but having four 2,000 lb capacity D-rings should be more than enough for most any truck camper. view full answer...
We do have the replacement plates for your front HappiJac Camper Tie-Downs # LC182908-182928. What you need is the Replacement Front Anchor Plates for HappiJac Truck-Mounted Camper Tie-Downs # LC58AF view full answer...
Hey Randall,
For a 1988 Ford F-250 you'll need the TorkLift Camper Tie-Downs - Front # TLF2000 and Rear # TLR3501. To secure your camper to the tie-downs you can use the TorkLift AnchorGuard Derringer Turnbuckles # TLS9020. view full answer...
No, due to changes over the years a 2023 Ford F-350 with an 8' bed and running boards that end at the cab or no running boards would require the TorkLift Camper Tie-Downs - Front # TL87CR and Rear # TLF3008. If you want the aluminum versions then you'd need part # TL36CR and # TLF3008A.
If you're in need of new turnbuckles then I recommend the TorkLift AnchorGuard Derringer Turnbuckles for Truck Camper Tie-Downs # TLS9020. view full answer...
Because you are using the TorkLift Front # TLD2140 and Rear # TLD3113 frame mounted Tie-Downs you are going to want to use their Turnbuckles # TLS9529-2-LK. This is due to the length of them as the Happy Jack # LC182898 have shorter turnbuckles due to them using a bed mounted front anchor. The TorkLift Turnbuckles # TLS9529-2-LK come with locks as well to protect your investment. view full answer...
We have the TorkLift Camper Tie-Downs Front # TLD2142 and Rear # TLD3112 for your 2023 Ram 3500 Crew Cab long bed dually with the factory running boards. You may need the Anchor Relocation Kit # TLA7004 if your slide in camper is less than 90" from the front slide in portion to the rear anchor points. I recommend using the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK to secure your camper in the bed. These have a stainless steel construction for corrosion protection and a black powder... view full answer...
Hello!
I recommend using the HappiJac Camper Tie-Downs # LC182910-182971 for your application because the anchors install in the front of your bed and at your bumper so you don't have to mess with anything under your truck.
We don't ship to France but you might be able to find an in-between company who can ship it internationally for you. Please note this kit has only been confirmed to fit the US model of this truck. If your truck is a European model then I don't have a way to confirm... view full answer...
The biggest difference between the TorkLift Camper Tie-Downs # TL84FR, # TL44FR & the TorkLift Talon Camper Tie-Downs # TL73QR & # TL44XR is that the Talon's are made of Aluminum which is going to be approximately 30-50% lighter than the traditional steel tie downs.
Other than that, they are the exact same and will do the same job. The other caveat is the aluminum Talon tie downs are also going to quite a bit more expensive.
With either choice you are also going to need a set of turnbuckles... view full answer...
Since you have running boards that run all the way to the rear, the only cusotm tie downs available for your 2021 GMC Sierra 1500 are for the rear using the TorkLift Camper Tie-Downs - Custom Frame Mount # TL54FR.
To properly install your pop up camper in your truck you're going to need all 4 tie downs, so the only way you'd be able to do that is if you used # HSSF which is an in bed tie down. view full answer...
The correct tie-downs for your 2019 Ram 3500 Tradesman short bed depend on your hitch. You can choose from the following:
With a factory installed hitch or non-Torklift aftermarket hitch
-TorkLift Talon Camper Tie-Downs # TL52XR (front) and # TL34FR (rear)
or
-TorkLift Camper Tie-Downs # TLD2141 (front) and # TLD3112 (rear)
With a TorkLift SuperHitch Magnum 30K
-TorkLift Camper Tie-Downs # TLD2141 (front) and # TLR3510 (rear)
Keep in mind, none of these will fit if you have the aftermarket... view full answer...
You will want a bow/stern tie-down for each kayak so the Yakima Bow/Stern Tie-Down Ropes w/ Ratchets and Strap Loops # Y04031 will cover the other two kayaks. You may also want the # Y07416 to go with them.
I reached out to Yakima about the additional cinch straps and they said it all depends on the size of the kayaks. They said if they're too wide additional straps # Y05006 are necessary and said it would be best to get the straps just in case since you will regularly carry three. They... view full answer...
Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for.
For the front, you'll want the TorkLift Camper Tie-Downs # TL87CR (TorkLift P/N F2032), and for the rear you'll want the TorkLift Camper Tie-Downs # TLF3008 (TorkLift P/N F3008).
In addition to the tie downs, you're also going to need a set of turnbuckles # TLS9529-2-LK to secure your camper to the vehicle. view full answer...
Hello Jerry, I am sorry to say that we do not offer any custom fitted camper tie downs for a 2024 Nissan Titan XD. We carry both the Torklift and Happijack brand tie downs and neither of these manufacturers make anything for this vehicle. It may be possible to use some universal no-drill bed-mounted tie downs like the Brophy # HSSF, but we have not tested for fitment so we cannot confirm that they will work. I have linked the review video and installation instructions below if you want... view full answer...
The correct camper tie-downs for your 2023 F-350 DRW are the TorkLift Camper Tie-Downs - Front # TL87CR and TorkLift Camper Tie-Downs - Rear # TLF3008 view full answer...
Hey Kenneth, thanks for the question and the answer is yes, TorkLift tie-downs are specific not only to the year make and model, such as the 2014 Ford F-350, but also specific to the length of your bed, if you have running boards, and the hitch you have. For example, on a 2014 Ford F-350 with a 6-3/4' bed, no running boards under the bed, and a factory hitch you would use the TorkLift Camper Tie-Downs - Front # TLF2012 and Rear # TLF3006.
Or for a '14 F-350 with an 8' bed, no running... view full answer...
That's a great question Mike and I have an interesting answer. There actually isn't any specific weight capacity for the HappiJac Truck-Mounted Camper Tie-Downs item # LC182910-182971.
These are designed to handle the weight of any truck bed camper, and that's true of any camper tie-down, which is why there isn't a designated weight rating. If a camper can fit inside the bed of your F-350, the HappiJac tie-downs will safely hold it in place.
The only other thing you will need with these... view full answer...